Machine parts
Shafts, gears, and machine components.
Stainless Steel Round Bar | Duplex Steel Round Bar | High Nickel Alloy Round Bar
Grade 304 · Austenitic stainless steel
SS 304 round bar is an austenitic chromium-nickel stainless steel product identified as UNS S30400, EN 1.4301 and SUS 304. It is used for machined and fabricated components where the specified corrosion resistance, mechanical properties and finish meet the service requirements.
Specify the governing standard, diameter, length, condition, finish, tolerance, testing, documentation, and destination. Use the values below for initial comparison and confirm acceptance limits against the purchase specification.

At a glance
The 3–500 mm diameter and 3–6 m length ranges are values stated in the source page, not a live stock commitment. Confirm availability for the exact size, grade standard and condition.
Grade overview
Stainless Steel 304 round bar is a solid, cylindrical product made from austenitic chromium-nickel stainless steel. The grade is commonly identified as UNS S30400, EN 1.4301 or SUS 304 under the relevant standard. Its combination of corrosion resistance, formability and general-purpose mechanical performance makes it useful for machined parts and fabricated equipment.
Grade 304 is not automatically suitable for every marine, chloride-rich or high-temperature service. Material choice should consider exposure, design, welding requirements and the applicable purchasing specification. For welded assemblies where sensitization is a concern, buyers may also compare Stainless Steel 304L Round Bar.
Buyer selection guide
Start with the drawing or purchase specification, not the grade name alone. Grade 304 identifies the material family; the standard, product form, dimensions, condition, finish, tolerance, and verification requirements define what must be supplied.
Applications
The following applications may specify SS 304 round bar. Check suitability against the design and service conditions.
Shafts, gears, and machine components.
Engine components, fasteners, and suspension components.
Conveyors, mixers, and storage equipment.
Structural components, frames, and support rods.
Certain fittings and hardware, subject to chloride exposure, corrosion assessment and project specifications.
Confirm material suitability and any regulated-use requirements for the equipment.
Specifications
| Diameter | Length | Standards listed |
|---|---|---|
| 3–500 mm | 3–6 metres | ASTM A276, ASTM A479, EN 10088-3, JIS G4303 |
| Custom sizes stated | Custom lengths stated | Custom specifications stated |
Confirm the condition, tolerance, finish and diameter during quotation.
Chemical composition
Composition by mass; confirm limits against the specified standard.
| Element | Symbol | Reference value (%) | Qualifier |
|---|---|---|---|
| Carbon | C | 0.08 | Maximum |
| Chromium | Cr | 18.00–20.00 | Range |
| Nickel | Ni | 8.00–10.50 | Range |
| Manganese | Mn | 2.00 | Maximum |
| Silicon | Si | 1.00 | Maximum |
| Phosphorus | P | 0.045 | Maximum |
| Sulfur | S | 0.030 | Maximum |
Composition limits depend on the applicable standard and edition. Confirm the specified chemistry before ordering.
Mechanical properties
Reference properties; confirm the required supply condition and standard.
| Property | Reference value | Qualifier |
|---|---|---|
| Tensile strength | 515 MPa | Minimum |
| Yield strength | 205 MPa | Minimum |
| Elongation | 30% | Minimum |
| Reduction of area | 40% | Minimum |
| Hardness | 237 HB | Maximum |
| Modulus of elasticity | 193 GPa | Confirm acceptance limit |
Mechanical-property acceptance limits depend on the standard, product condition, size and test method. Confirm these requirements in the purchase specification.
Equivalent grades
| Standard or system | Designation |
|---|---|
| ASTM A276 / ASTM A479 | UNS S30400 |
| EN 10088-3 | DIN 1.4301 |
| JIS G4303 | SUS 304 |
Interchangeability notice: a designation cross-reference does not establish direct interchangeability. Confirm composition, properties, dimensions, testing, condition, and project requirements under the governing standard.
State the required heat number, grade, size and manufacturer marking in the purchase specification, together with traceability documents.
Technical considerations
The designation “304” does not define every chemical, mechanical, dimensional, testing, or documentation requirement. The purchase order should name the governing standard and edition.
Confirm the product condition, diameter, specimen direction, test method and temperature before using mechanical-property values for design calculations.
UNS S30400, DIN 1.4301, and SUS 304 help identify the grade across designation systems. They do not by themselves prove full interchangeability under a project specification.
State the service environment, fabrication route, loads, cleaning exposure, surface requirement, inspection plan, and documentation needs so the material requirement can be reviewed properly.
Product questions
SS 304 round bar is a solid cylindrical austenitic stainless steel product commonly specified for machined parts, shafts, fittings and fabricated equipment. The applicable product standard and service environment determine suitability.
The UNS designation is S30400. Related designations include EN 1.4301 and JIS SUS 304. These cross-references do not replace checking the governing standard and edition.
Commonly referenced bar standards include ASTM A276, ASTM A479, EN 10088-3 and JIS G4303. Choose the standard specified by your drawing or purchase order.
Reference ranges include 18–20% chromium and 8–10.5% nickel, with maximum carbon of 0.08%. Check the full composition table and the required standard for acceptance limits.
The source page lists diameters of 3–500 mm and lengths of 3–6 m. You can specify the required diameter, tolerance, length, surface finish and delivery condition; availability must be confirmed by quotation.
Provide the grade and governing standard, diameter, length, quantity, delivery condition, tolerances, finish, test certificates, inspection needs and destination. Include a drawing when the part has special requirements.
Related products
Specification-led enquiries
Include the governing standard, diameter, length, quantity, condition, finish, testing requirements, and delivery destination for a useful commercial response.
