Stainless Steel 303 Round Bar

Stainless Steel Round Bar

Stainless Steel 303 Round Bar Manufacturer, Supplier and Exporter

Stainless Steel 303 round bar (UNS S30300) is a free-machining austenitic stainless steel selected for precision-turned parts, shafts, fasteners and fittings. Added sulfur helps chip breaking during machining. Grade selection must also account for corrosion exposure and fabrication requirements.

Specify the product standard, diameter, required supply condition, tolerance, testing and destination when requesting material. For other austenitic grades, see Stainless Steel 304 round bar.

Representative stainless steel round bar product image
Representative stainless steel round bar image; confirm the specific grade with the material test certificate.

At a glance

Stainless Steel 303 Round Bar Quick Facts

Grade
303 austenitic stainless steel
UNS designation
S30300
European designation
EN 1.4305
Key characteristic
Improved machinability through sulfur addition
Common product standard
ASTM A276; confirm suitability and edition
Typical uses
Turned parts, shafts, fasteners, fittings

Actual dimensions, condition and certification are subject to confirmation for each order.

Material overview

What Is Stainless Steel 303 Round Bar?

Stainless Steel 303 is a chromium-nickel austenitic stainless grade developed for easier machining than conventional 304. Sulfur-containing inclusions help produce shorter chips during turning and drilling. The trade-off is lower resistance to some corrosive environments and reduced suitability for welding compared with 304.

It is commonly specified for production-machined components that do not require the corrosion performance of higher-alloyed grades. The selected bar must meet the drawing, specified standard, mechanical requirements and service conditions.

Buyer selection guide

How to Specify Stainless Steel 303 Round Bar

A complete enquiry should distinguish the grade from the standard and the required bar condition.

Grade and standardIdentify 303 / UNS S30300 and the controlling specification with edition.
DimensionsState diameter, cut length, quantity and dimensional tolerances.
Delivery conditionSpecify cold finished, hot finished, peeled, ground or another required finish where applicable.
Quality documentsDefine inspection, test certificates, traceability, marking and destination.

Technical information

SS 303 Round Bar Specifications and Applications

Applications of Stainless Steel 303 Round Bar

Grade 303 is commonly used for parts involving substantial turning, drilling or threading, where the operating environment is suitable for the alloy.

  • Machined shafts, spindles and pins
  • Screws, nuts, bolts and threaded components
  • Valve and instrument components, subject to application requirements
  • General precision-machined fittings and hardware

For more demanding corrosion service, compare the specifications for 304 and 316 round bars rather than choosing by machinability alone.

Stainless Steel 303 Round Bar Specifications

Sizes, finishes and mechanical acceptance limits depend on the ordered specification and condition. Do not treat indicative dimensions as confirmed stock.

RequirementDetails to confirm
GradeStainless Steel 303 / UNS S30300 / EN 1.4305
Product standardsASTM A276, ASTM A479 or EN 10088-3 as applicable to the purchase order
DimensionsDiameter, length, dimensional tolerances, straightness and end preparation
Surface / supply conditionHot finished, cold finished, peeled, ground or polished as specified
CertificationMaterial test certificate and additional inspection documents as ordered

Chemical Composition of Stainless Steel 303 Round Bar

The source page contains the following indicative composition. These figures are retained as reference data, not certified acceptance limits; verify each value against the governing standard and its edition, especially when a purchase order requires a specific chemistry.

ElementPercentage (%)
Carbon (C)0.10 max
Chromium (Cr)17.00 – 19.00
Nickel (Ni)8.00 – 10.00
Manganese (Mn)2.00 max
Silicon (Si)1.00 max
Phosphorus (P)0.20 max
Sulfur (S)0.15 min

Composition varies by governing specification. Refer to the approved standard and material test report for acceptance.

Mechanical Properties of Stainless Steel 303 Round Bar

These original page figures are indicative and should not be treated as guaranteed values. Mechanical requirements vary with diameter, product condition and governing specification.

PropertyValue
Tensile Strength515MPa
Yield Strength205 MPa (min)
Elongation30% min
Hardness237 HB (max)
Modulus of Elasticity193 GPa

Confirm actual test results and specification limits for the ordered bar.

SS 303 Equivalent Grades and Designations

Related grade designations are shown for identification. Equivalence does not authorize substitution without comparing the required standards and properties.

StandardEquivalent Grade
ASTM A276UNS S30300
EN 10088-3DIN 1.4305
JIS G4303SUS 303 Round Bar

Machining, Welding and Corrosion Considerations

The sulfur addition typically makes SS 303 easier to machine than SS 304. However, 303 is generally not recommended for welding, and its corrosion resistance is lower in certain environments. Select material based on service conditions, manufacturing method and applicable engineering requirements.

For related choices, explore the stainless steel round bar range and bright bars for finishing considerations.

Availability, Testing and Export Enquiries

Send the grade, required standard, diameter, quantity, finish, inspection requirements and delivery location to request current availability and pricing. Specify heat traceability and any third-party inspection requirement before placing the order.

Frequently asked questions

Stainless Steel 303 Round Bar FAQs

What is Stainless Steel 303 round bar?

Stainless Steel 303 is an austenitic stainless steel with sulfur added for improved machinability. Its UNS designation is S30300, and it is often used for turned components and fasteners.

Is SS 303 easier to machine than SS 304?

Generally yes. The sulfur addition in 303 helps chip breaking and machining productivity, but it can reduce corrosion resistance and weldability compared with 304.

What is the difference between UNS S30300 and EN 1.4305?

UNS S30300 and EN 1.4305 are closely related designations for free-machining stainless steel. They are not automatic substitutes; compare the applicable standard, chemistry and delivery condition.

Is Stainless Steel 303 suitable for welding?

Grade 303 is generally not preferred for welding because its sulfur content can increase the risk of cracking. Select another grade or obtain qualified welding guidance when welding is necessary.

Which standards apply to SS 303 round bars?

ASTM A276, ASTM A479 and EN 10088-3 may be relevant depending on the order and end use. The grade, product form, standard edition and condition must be confirmed before supply.

What details are required for an SS 303 round bar quotation?

Provide the grade or designation, diameter, length, quantity, required standard and edition, supply condition, dimensional tolerance, testing, certification and delivery destination.

Specification-led enquiries

Request a quote for Stainless Steel 303 Round Bar

Include the governing standard, dimensions, quantity, condition, testing requirements, documentation, and destination.

  • Grade and standard
  • Diameter and quantity
  • Condition, finish, or testing
  • Destination and required timing

Piyush Steel India

Request a quote

Share your product requirements with our sales team. All four fields are required.

Your details will be emailed to our sales team to respond to this enquiry.