Duplex Steel UNS S31803 Round Bar

Duplex Steel Round Bar

Duplex Steel UNS S31803 Round Bar Manufacturer, Exporter and Supplier

UNS S31803 is a duplex stainless steel grade with a combined ferritic and austenitic structure. It offers high yield strength and good resistance to pitting, crevice corrosion and chloride stress corrosion cracking in suitable service conditions.

This grade belongs to the 2205 family, but its chemistry limits differ from UNS S32205. When ordering round bar, specify UNS S31803, the material standard, diameter, length, solution-annealed condition and inspection documents.

Representative duplex steel uns s31803 round bar product image
Representative image for the Duplex Steel Round Bar product range.

At a glance

Duplex Steel UNS S31803 Round Bar quick facts

Product
Duplex Steel UNS S31803 Round Bar
Material category
Duplex Steel Round Bar
Product reference
Duplex Steel UNS S31803 Round Bar
Standards and designations referenced
UNS S31803; DIN 1.4462; ASTM A276
Enquiry details
Grade, dimensions and supply condition

Confirm the applicable specification and availability for your required size and condition.

Buyer selection guide

How to select Duplex Steel UNS S31803 Round Bar

Begin with the drawing, equipment specification, or governing code. The product name identifies the material route; acceptance depends on the complete purchase specification.

Material identityState Duplex Steel UNS S31803 and any required designation.
Governing standardSpecify UNS S31803 and the applicable ASTM A276/A276M or ASTM A479/A479M edition. Confirm EN 1.4462 where required.
Dimensions and conditionProvide diameter, length, quantity, tolerance, condition, finish, and machining allowance.
VerificationDefine testing, inspection, marking, traceability, documentation, destination, and timing.

Common applications

Where Is UNS S31803 Duplex Round Bar Used?

UNS S31803 round bars are used for machined parts that need both strength and corrosion resistance. Suitability must be checked against operating temperature, chlorides, loads and the governing design requirements.

  • Oil and gas equipment: valve stems, connectors and selected bolting.
  • Chemical processing: pump shafts, valve parts and fittings.
  • Marine and water systems: rotating shafts and other mechanical parts exposed to chloride-containing water.
  • Pulp and paper plants: shafting and components in aggressive process environments.
  • General engineering: high-strength pins, fasteners and machined bar components.

Compare the duplex round bar range and super duplex round bars when higher localized-corrosion resistance is being considered.

Specifications

UNS S31803 Round Bar Standards and Supply Details

Specify the exact UNS grade and product standard for acceptance. The name 2205 alone does not establish the certified chemical limits or bar condition.

RequirementInformation
Material gradeUNS S31803 duplex stainless steel (2205 family)
European referenceEN 1.4462 / X2CrNiMoN22-5-3 (confirm applicable standard)
General bar specificationASTM A276/A276M, where applicable
Pressure-service bar specificationASTM A479/A479M, where applicable
ConditionSolution annealed and cooled as required by the product specification
DimensionsDiameter, length, straightness and dimensional tolerance as ordered
Surface finishHot finished, peeled, turned or ground, subject to availability
InspectionMill test certificate with heat number, chemical and mechanical results; additional tests as specified

For exact dimensional tolerance, specify the tolerance class and diameter on the purchase order. The incomplete ISO tolerance chart in the original page has been removed to avoid misleading values.

For related finishes see bright round bars and forged bars.

Chemical composition

UNS S31803 Chemical Composition

These are widely referenced chemical-composition limits for UNS S31803, in percent by mass. The exact requirement is controlled by the specified standard and edition. Do not substitute the narrower UNS S32205 chemistry limits.

ElementUNS S31803 (wt. %)
Chromium (Cr)21.0–23.0
Nickel (Ni)4.50–6.50
Molybdenum (Mo)2.50–3.50
Nitrogen (N)0.08–0.20
Carbon (C)0.030 maximum
Manganese (Mn)2.00 maximum
Silicon (Si)1.00 maximum
Phosphorus (P)0.030 maximum
Sulfur (S)0.020 maximum
Iron (Fe)Balance

Confirm actual chemistry and heat identification using the mill test certificate.

Mechanical properties

Mechanical Properties of UNS S31803 Round Bar

The following are reference requirements for solution-annealed UNS S31803 bars in published ASTM A276 editions. Bar size, processing and the applicable standard edition must be checked before acceptance.

PropertyPublished reference value
Minimum tensile strength620 MPa (90 ksi)
Minimum 0.2% yield strength448 MPa (65 ksi)
Minimum elongation25%
Maximum Brinell hardness290 HB (published ASTM A276 reference)
Supply conditionSolution annealed
Magnetic behaviourNormally magnetic due to ferrite content

These values are not a substitute for the controlling purchase specification and certified test results. Other standards may round 448 MPa to 450 MPa.

Technical considerations

What to verify before specifying Duplex Steel UNS S31803 Round Bar

Standard and edition

Confirm the controlling document; a grade name or cross-reference alone is not a complete acceptance specification.

Product condition

Check that property values apply to the required diameter, heat treatment, test direction and temperature.

Dimensions and finish

State tolerances, straightness, length, surface finish, machining allowance, and end condition where required.

Evidence and traceability

Define inspection, test reports, marking, heat identification, third-party requirements, and destination documentation.

Grade designations

UNS S31803 and Related Duplex 2205 Designations

DesignationRelationship
UNS S31803Specified grade on this page
Duplex 2205Common duplex grade family name
EN 1.4462Related European designation; verify the selected edition
SAF 2205Commercial name used within the duplex 2205 family
UNS S32205Related grade with tighter chemistry requirements; not automatically interchangeable

Compare UNS S32205 round bar and SAF 2205 round bar for project-specific grade selection.

More about the material

More About UNS S31803 Duplex Round Bar

How Does Surface Finish Affect Machining?

Hot-finished bars may require extra machining allowance for final diameter and finish. Peeled, turned or ground products can reduce preparation work when tighter tolerances are needed. Confirm the supplied diameter, straightness and cut length before machining. See bright bar finishes for related options.

Why Does Solution Annealing Matter?

Solution annealing and controlled cooling help maintain the intended ferrite-austenite balance. Incorrect thermal processing may allow unwanted phases that reduce toughness and corrosion resistance. The required delivery condition should match the product specification and service application.

How Should Material Traceability Be Maintained?

Keep the heat number with each bar and cut piece throughout storage and machining. Match the mill test certificate to the UNS S31803 grade, chemistry, mechanical results and purchase order. Additional corrosion or microstructure testing may be needed for critical projects. See quality assurance information.

Frequently asked questions

UNS S31803 Duplex Steel Round Bar FAQs

What is UNS S31803 duplex stainless steel?

UNS S31803 is a duplex stainless steel containing ferrite and austenite. It offers high strength and corrosion resistance for suitable chemical, marine and industrial conditions.

Is UNS S31803 the same as UNS S32205?

They belong to the duplex 2205 family but have different chemistry ranges. S32205 specifies tighter chromium, molybdenum and nitrogen limits. Check the UNS grade required by the drawing and certificate.

Which ASTM standards are used for S31803 round bars?

ASTM A276/A276M covers stainless steel bars and shapes, while ASTM A479/A479M may apply to pressure-service bars. Confirm that the chosen grade and condition are covered in the specified edition.

Is UNS S31803 round bar magnetic?

Yes. Its ferrite phase normally gives duplex S31803 a magnetic response, even when properly solution annealed.

Can UNS S31803 round bars be machined?

Yes. Because of the grade's high strength, suitable tooling, cutting speeds and secure workholding are important. Specify the finished diameter and tolerance before ordering.

Why is solution annealing important for S31803?

Correct heat treatment and cooling help provide the intended duplex microstructure. Poorly controlled processing can reduce corrosion resistance and toughness.

How should UNS S31803 round bars be stored before machining?

Keep the bars dry, supported and separated from carbon steel dust and grinding debris. Preserve heat numbers and labels so every cut piece remains traceable to its material certificate.

Specification-led enquiries

Request a quote for Duplex Steel UNS S31803 Round Bar

Include the governing standard, dimensions, quantity, condition, testing requirements, documentation, and destination.

  • Grade and standard
  • Diameter and quantity
  • Condition, finish, or testing
  • Destination and required timing

Piyush Steel India

Request a quote

Share your product requirements with our sales team. All four fields are required.

Your details will be emailed to our sales team to respond to this enquiry.