Alloy Steel 34CrNiMo6 / 1.6582 Round Bar

Nickel-chromium-molybdenum alloy steel

34CrNiMo6 (1.6582) Round Bar Manufacturer, Exporter and Supplier

34CrNiMo6 (1.6582) round bar is a nickel-chromium-molybdenum alloy steel used for high-strength engineering components. It is commonly supplied in a quenched and tempered condition for parts that need strength, toughness and good hardenability.

Piyush Steel India handles enquiries for 34CrNiMo6 alloy steel round bars for shafts, gears, axles and other heavily loaded parts. Share your diameter, length, required condition, standard and test certificate requirements so the material and availability can be confirmed before quotation.

Product information by Piyush Steel India

Representative 34CrNiMo6 1.6582 alloy steel round bars
Representative image of our alloy steel round bar range. Actual surface condition depends on supply.

At a glance

34CrNiMo6 / 1.6582 Round Bar Quick Facts

EN steel grade
34CrNiMo6
Werkstoff number
1.6582
Alloy type
Nickel-chromium-molybdenum engineering steel
Reference standard
EN ISO 683-2 (hot-rolled steel; confirm edition and supply route)
Common heat treatment
Quenched and tempered (+QT)

Mechanical properties vary by size, processing route and heat-treatment condition.

Buyer selection guide

How to Choose 34CrNiMo6 Round Bar

Start with the component drawing and confirm that 34CrNiMo6 (1.6582) is the specified grade. For engineering parts, the material designation alone is not enough: strength and toughness depend on the product size and supply condition.

Grade and standardSpecify 34CrNiMo6 / 1.6582 and the applicable EN ISO 683-2 or other agreed product standard.
DimensionsProvide diameter, cut length, quantity, tolerances and any machining allowance. Use our round bar weight calculator for a starting estimate.
ConditionState whether you need hot-rolled, annealed, quenched and tempered, or a bright-finished bar, subject to supply.
InspectionConfirm required mechanical tests, heat identification and EN 10204 certificate type before ordering.

Engineering uses

Applications of 34CrNiMo6 / 1.6582 Round Bar

The strength and hardenability of this grade make it a practical choice for components that experience high loads or repeated stress, when properly specified and heat treated.

  • Transmission shafts and gear shafts: parts that transfer torque and need strength through the section.
  • Heavy-duty axles and pins: components exposed to bending and impact loading.
  • Forged machine parts: connecting elements, couplings and other highly stressed components.
  • Automotive and mechanical equipment: parts where a balance of strength and toughness is required.

For other steel families and grades, browse our alloy steel round bar range. Final selection must follow the design requirements of the component.

Material specifications

34CrNiMo6 Round Bar Standards, Sizes and Supply Conditions

34CrNiMo6 round bar dimensions and availability depend on the selected supply condition and order quantity. We recommend confirming size rather than relying on a generic stock range.

SpecificationDetails
Grade34CrNiMo6 / Werkstoff 1.6582
Reference specificationEN ISO 683-2 for relevant hot-rolled products; EN 10277 for applicable bright products
Product formRound bar; other forms subject to enquiry
Typical supply conditionsHot-rolled, annealed, quenched and tempered (+QT), or bright-finished, subject to enquiry
Diameter and lengthConfirm size, tolerance, weight and cut length with the sales team
Surface finishHot-rolled, peeled, turned or bright condition as specified
DocumentationMill test certificate; EN 10204 3.1 or other agreed inspection requirements where available

Compare relevant product forms such as hot-rolled bars and bright bars before placing an enquiry.

Chemical composition

34CrNiMo6 / 1.6582 Chemical Composition

The following values are reference cast-analysis limits in weight percent for 34CrNiMo6 under EN ISO 683-2. Always use the agreed specification edition and the actual mill certificate for acceptance.

ElementContent (% by mass)
Carbon (C)0.30–0.38
Silicon (Si)0.10–0.40
Manganese (Mn)0.50–0.80
Phosphorus (P)0.025 max.
Sulphur (S)0.035 max.
Chromium (Cr)1.30–1.70
Nickel (Ni)1.30–1.70
Molybdenum (Mo)0.15–0.30

The combination of nickel, chromium and molybdenum supports hardenability and toughness after suitable heat treatment. This is an alloy engineering steel, not a stainless steel.

Mechanical properties

34CrNiMo6 Mechanical Properties in the +QT Condition

These are reference mechanical property values for quenched and tempered hot-rolled bars, grouped by diameter. Strength typically varies with section size and final processing. Values for other product forms or conditions should not be taken from this table.

Diameter (mm)0.2% proof strength min. (MPa)Tensile strength (MPa)Elongation min. (%)Reduction of area min. (%)
Up to 161,0001,200–1,400940
Over 16 to 409001,100–1,3001045
Over 40 to 1008001,000–1,2001150
Over 100 to 160700900–1,1001255
Over 160 to 250600800–9501355

Reference: Rodacciai technical data for EN ISO 683-2 hot-rolled 34CrNiMo6. Confirm the current standard edition, impact requirements, test direction and values applicable to the actual order.

For material verification and documentation, see our quality assurance information.

Before ordering

What to Check Before Ordering 34CrNiMo6 Bars

Heat-treated condition

State +QT or the intended condition. Do not compare hardness and tensile values without checking the heat-treatment state.

Size and core properties

Bars with different diameters may not have identical strength or toughness at the core. Match the table to the order size.

Machining and finish

Confirm surface finish, allowance for machining, straightness and any end preparation required by your drawing.

Certificate and traceability

Request test reports, heat number and marking requirements when preparing the purchase specification.

Grades and designations

34CrNiMo6 (1.6582) and Comparable Grades

34CrNiMo6 and 1.6582 refer to the same EN material designation. AISI 4340 / UNS G43400 is often used as a comparison, but it should not be treated as an automatic substitute: chemistry limits, mechanical requirements and product specifications can differ.

Designation systemGrade / guidance
EN grade34CrNiMo6
Material number1.6582
Comparable US gradeAISI 4340 / UNS G43400, subject to engineering verification
Other market designationsEN24 / 817M40, sometimes compared; verify before substitution

If you are comparing engineering steels, you can also review AISI 4340 round bar and AISI 4140 round bar. Use the controlling drawing and material specification to determine suitability.

Practical technical guidance

More About 34CrNiMo6 Alloy Steel Round Bar

Why Is 34CrNiMo6 Used for High-Load Shafts?

The alloying elements improve hardenability, allowing suitable heat treatment to develop strength through thicker sections than many simpler steels. That makes it useful for torque-carrying shafts and other loaded machine parts. The finished design still needs checks for fatigue, impact loading, diameter and operating conditions.

Does 34CrNiMo6 Need Quenching and Tempering?

34CrNiMo6 is frequently specified in the quenched and tempered (+QT) condition when a balance of strength and toughness is required. The heat-treatment cycle should be selected for the part size and target mechanical properties. If machining is planned, confirm whether annealed material or +QT material is the better starting condition.

What Details Should Be Included in a 34CrNiMo6 RFQ?

Provide the grade (34CrNiMo6 / 1.6582), governing standard, diameter, length, quantity, surface finish and heat-treatment condition. Add mechanical or impact test requirements, tolerances, required certificate type, delivery location and timing. This helps the supplier quote material that actually matches the job.

Buyer questions

34CrNiMo6 / 1.6582 Round Bar FAQs

What is 34CrNiMo6 round bar?

34CrNiMo6 is a nickel-chromium-molybdenum alloy steel used for high-strength engineering components. Material number 1.6582 identifies the grade in the EN system. It is often specified in a quenched and tempered condition for machine parts that require both strength and toughness. Confirm the required product standard and supply condition before ordering.

Is 34CrNiMo6 the same as 1.6582?

Yes. 34CrNiMo6 is the EN steel grade designation and 1.6582 is its material number. Both names identify the same grade family. They do not, by themselves, define the bar dimensions, heat-treatment condition or mechanical acceptance requirements. Those details must be specified separately in the enquiry and purchase order.

Is 34CrNiMo6 equivalent to AISI 4340?

AISI 4340 is often listed as a comparable grade because both are nickel-chromium-molybdenum engineering steels. However, they are not interchangeable for every specification or application. Chemical limits, heat treatment, section size, testing and acceptance criteria may differ. Ask your engineer to verify equivalence against the drawing before substituting one for the other.

What are the main applications of 34CrNiMo6 bars?

Common applications include transmission shafts, gear shafts, axles, heavy-duty pins and forged machine components. The grade is chosen where a combination of high strength and toughness is needed. Actual suitability depends on loads, fatigue requirements, operating temperature, geometry and heat treatment. The component specification should determine the final material choice.

Which standard applies to 34CrNiMo6 round bar?

EN ISO 683-2 is a relevant reference for certain hot-rolled products, while EN 10277 covers applicable bright products. A finished bar can also be supplied to another agreed product specification. State the required standard, edition, size and condition on your enquiry, and confirm that the inspection certificate reflects that specification.

How do mechanical properties change with bar diameter?

The mechanical properties of quenched and tempered 34CrNiMo6 depend on diameter and heat treatment. Reference tables show different minimum proof strengths and tensile ranges for different bar sizes. Do not use the highest strength listed for a large bar without checking the correct size range. Confirm the actual requirements using the agreed material standard and test certificate.

What information is needed for a 34CrNiMo6 round bar quotation?

Send the grade or material number, required diameter and length, quantity, product standard, tolerance and surface finish. Specify whether annealed or quenched and tempered material is needed. Add test certificates, inspection requirements, delivery destination and requested schedule. You can then receive a quotation based on the defined material condition and supply requirements.

Specification-led enquiries

Request a quote for Alloy Steel 34CrNiMo6 / 1.6582 Round Bar

Include the governing standard, dimensions, quantity, condition, testing requirements, documentation, and destination.

  • Grade and standard
  • Diameter and quantity
  • Condition, finish, or testing
  • Destination and required timing

Piyush Steel India

Request a quote

Share your product requirements with our sales team. All four fields are required.

Your details will be emailed to our sales team to respond to this enquiry.